I might as well post here since you guys are fairly close to me.
My financial situation is the worst it's been in my life, and making $20 sales here and there won't help me at all. I must get rid of all this stuff at once.
- 92 VR4 Rolling chasiss with title
- 4 bolt bare block with broken axle locator pin bosses (can be repaired or used for a RWD monster)
- 4 bolt broken block
- 2 bolt bare block qty 3
- 3.5L shortblock
- 3.5L plenum
- 3.5L lower intake
- 3.5L throttle body
- 3.0L lower intake qty 3
- 12 pistons
- 12 rods
- 1 forged crank, needs turning
- 3 cast cranks, need turning
- 1g TT bare heads
- 2g TT bare heads
- valves, springs, and cams for above
- 2.6L non-jet valve head
- Various 3/s turbos
- 15 3/s wastegate accuators
- a few 14b turbos
- Transfer case tail section with shaft and gear (5 speed)
- 2+ alternators
- 2+ starters
- 10 calipers (need rebuilding)
- 2g TT downpipes, qty 2
- 2 TT flywheels
- Right rear control arm
- Left and right front crossmembers and then some
- Complete TT driveshaft qty2
- 5 rear axles
- a few front axles
- water neck
- Complete 91-92 body harnesses
- Various other harnesses
- All Intercooler pipes and hoses and then some
- Intercoolers
- Intake hoses
- Many exhaust manifolds/precats/o2 housings
- 1g TT front hubs/knuckles
- 2 interior door panels
- Enough misc brackets to assemble 3 motors
- 2g oil pan
- 5 oil pumps
- water pump
- Misc timing covers
- 10 cam gears/cogs
- 3 crank cogs
- 2 crank pulleys
- p/s pump
- 8 exhaust tips
- 2 stock cat-backs
- many rotors
- F&R steering racks
- 2 starter harnesses
- 2g headlight internals (2 lights)
- box of 10mm bolts
- box of 12mm bolts
- Box of 14mm bolts
- Box of 17mm bolts
- 1 headlight motor
- Many rear valve covers
- 2 front valve covers
- Box of harness plugs/pigtails
- Box of interior switches/trims
- Glovebox
- a few stock pressure plates
- Some brake and clutch masters and slaves
- a couple/few rear view mirrors
- many strut harness caps
- a few ecs struts
- Prototype oil feed fittings
- Some hatch struts
- Some wiper arms
- some wiper motors
- Washer fluid resivoir
- Some ABS sensors
- 1g CAS
- a few FPR's
- a few TPS's
- a few ISC's
- MAS
- Many injectors
- Many rocker arms
- Many lifters
- A few fuel rails
- 2 fuel pumps
- fuel pump assy
- Box of lugnuts
- set of wheel locks with key
- Box of solonoids
- Box of misc pulleys
- some 2g cam and crank sensors
- some coils
- Air filter box
- some dipsticks & tubes
- Front strut bar
- Misc hoses
- Misc engine bay items
- Box of "special" fasteners
NEW Items- 2 sets clevite rod bearings
- 2 sets clevite main bearings
- 3.5L dohc timing belt
- inner or outer (or both) rear axle bearings, can't remember which
- set of ngk non resistor plugs, heat range 8
- misc turbo gaskets
- 5 caliper rebuild kits
- Box of metric to AN adaptors
- Approx 500' of silicone hose, various sizes and colors
- 2" silicone I/C hoses (some red, some black)
- misc stuff
OEM Paper service manuals- 91 3000gt volume 1&2
- 92-96 3000gt volume 1&2
- 96 Montero volume 1 (engine, chassis, body)
- 92-96 engine overhaul (4g1, 4g3, 4g6, 4g9, 6g7, 4g6, 420a)
Mitchell collision estimating guideAsian Book 1&2, 2001 edition
There are more details here
http://www.us3s.com/freeforum/showthread.php?t=4446
